Categories
BLOG

how to use dr dabber

How to use dr dabber

No Products in the Cart

title

  • details
  • Sign In
  • Register
  • View Cart
  • Home
  • Boost Support

Swapping your Boost Nail
Unscrew Nail: Turn counterclockwise to unscrew nail, then lift nail to remove.
Lower nail and rotate clockwise to screw nail onto eRIG™.
*WARNING: DO NOT ATTEMPT TO REMOVE NAIL WHEN HOT. DO NOT TOUCH CERAMIC ROD AS IT MAY DAMAGE HEATING ELEMENT.

Boost Glass Removal
Between your index finger and your thumb, firmly hold the base of the glass unit AS WELL AS the glass ring that attaches to the device, then push down with caution until the attachment is flush with the lip of the Boost unit.

Do not hold from base alone (water chamber) as the joint may break when attaching the glass. Remove glass with a straight up and down motion. Try not to twist. Hold the glass attachment by the connection port.

Cleaning your Glass attachment
To clean glass attachment, first remove the glass attachment from the eRig, then slowly pour 99% isopropyl alcohol into the mouthpiece until the unit is about 1/4 full.

Shake the attachment gently until clean. To rinse out the alcohol, pour water into the top (mouthpiece) until all alcohol is flushed out of the bottom of the attachment.

To remove all water from device, blow through mouthpiece and shake gently.

Charging your boost
Insert the Micro USB charger into the side of the Boost, then insert the other side of the charger into a USB port or AC adapter.

The power button shows a purple light when the device is being charged. A green light indicates charging is complete. Due to the size of the battery, it is recommended to charge 6-8 hours or overnight on an AC adapter to charge fully.

Try to remove the charging cord as soon as the unit is fully charged, as the cord will not stop the trickle down effect, meaning it will slowly start to lose power over time after a full charge, while plugged in. You can always just unplug and plug the unit back in to check if it needs a few more minutes for a full charge.

Please, be advised our charger for the Boost will charge the battery to about 20 to 30 cycles. If you use an external 18650 battery charger, you will get an approximately 50 cycles. This happens for all USB chargers. They do not put out enough amps to get the battery to its full performance. We use these chargers for the convenience it provides with today’s technology.

How to use your Boost
1. Load Water (Remove glass before loading)
2. Click button * 3 times for titanium nail * 5 times for ceramic nail
3. Load product on tip of tool
4. Touch tip of the tool to nail once light changes color, then begin to inhale through glass mouthpiece.
5. Once all product has melted off of tool, flip tool around and place carb cap on top of the nail to increase vapor density.(Generally 3-4 seconds)

Is there a warranty on my boost
Unfortunately, we no longer carry or cover this model of Boost unit under our warranty. Check out our new model, the Boost: Black Edition.

Swapping your Boost Nail Unscrew Nail: Turn counterclockwise to unscrew nail, then lift nail to remove. Lower nail and rotate clockwise to screw nail onto eRIG™. *WARNING: DO NOT ATTEMPT TO REMOVE NAIL WHEN HOT. DO NOT TOUCH CERAMIC ROD AS IT MAY DAMAGE HEATING ELEMENT. Boost Glass Removal Between your index finger a

Dr. Dabber Switch Vaporizer Quickstart Guide

Follow along with this Quickstart guide to get going with your Dr. Dabber Switch!

The Dr. Dabber Switch vaporizer may intimidate first-time users and newcomers alike. Luckily, this quickstart guide will cover all of the basics to get you going with your new dab rig!

Dr Dabber Switch Quickstart: What’s in the box

  • Dr. Dabber Switch Vaporizer
  • Battery Pack
  • Glass Percolator Attachment
  • White Ceramic Induction Cup (Oil)
  • Black Ceramic Induction Cup (Leaf)
  • Ceramic Leaf Filter Cap
  • Glass Loading Tool & Carb Accessory
  • Reverse Action Tweezers
  • Silicone Storage Container
  • Charging Cable and Adapter
  • Instruction Manual

Charge it

To start off, let’s top off your Dr. Dabber Switch with a full charge. Grab the included power adapter and plug it into your Switch, and into a power source. Leave it plugged in until the red light on the power adapter turns from red to green, indicating a full charge. Flip the power switch to any mode and the Switch’s light band will light up to indicate its current charge.

Fill the bubbler

Before we put the Switch together, let’s fill the bubbler with water. Pour water into the mouthpiece, until it fills just past the percolator holes. Don’t fill it too much higher than the percolator or you’ll get water in your mouth. Connect the bubbler to the top of your Switch and give it a few test pulls to make sure it’s filled to your liking.

More water than this and you might get your lips wet!

Test run

Let’s make sure your Switch is in working order before we load it up with concentrates. Flip the power switch to the left, or into oil mode, and look for the yellow LED light band to turn on. Use the + button to raise the temperature to its highest level (five yellow lights). With the reverse tweezers, load an empty induction cup into the bottom of the well. Press the center “Go” button and let it run a full cycle. Notice how the top lights are Red when heating up, and turn Green when it’s ready to hit.

Oil: Choose your temp

With the power switch turned to oil mode, use the + – buttons to choose your desired temperature. Level One is best for maximum flavor, while Level Five is best for maximum vapor density. For this first session, try the middle temperature, or the third yellow light.

Load your cup

The Switch can be heated up first, and then loaded, just like a traditional torch and banger, but we’ll preload it first for this initial session. Take the ceramic cup out of the Switch with the reverse tweezers, and load it with a rice-grain sized amount of your chosen concentrate. Use the tweezers to place the cup into the bottom of the glass well, put the carb cap on top, and get ready for take off.

This load was on the bigger side. Took two sessions to finish off.

Fire it up

Once you’re ready for your first hit, press the “Go” button to engage the heater. The LED light band will turn red and escalate to indicate that it’s heating. It will turn green when it’s ready to go. The Switch’s unmatched heat up time will have it ready within seconds, so be ready! Once the lights turn green, you’ll have 15 seconds to hit it until the heater shuts off. Press the Go button anytime before then to manually end the session.

Advanced mode

This Quickstart Guide is meant to quickly get you up and running with your first dab. Once you’re ready for more than the stock five temperatures, it’s time to play with Advanced mode. While the Switch is off, hold in the Go button and flip the toggle button to oil mode. The lights will turn multi-colored if you did it correctly. Now you have 25 temperature settings, from 300° F to 800° F (148° C – 426° C) in 20 degree increments!

For dry herbs

We didn’t cover Leaf mode for the Switch because we don’t consider it a dry herb vaporizer. It’s more of an herbal smoker that gently heats your herbs, producing a light vapor at first that quickly gives way to smokiness. We highly recommend a dry herb vaporizer for your loose leaf herbs.

Cleanup

The Switch makes cleaning an absolute breeze with its self cleaning mode. Press and hold the + button until it reaches the highest level and continue holding for five more seconds. Release the button once the lights turn Red, and let it run its full cycle. Easy as that!

The Dr. Dabber Switch vaporizer may intimidate first-time users and newcomers alike. Luckily, this quickstart guide will cover all of the basics to get you going with your new dab rig!