Categories
BLOG

how to make an aluminum pipe

How to make a pipe out of aluminum foil

We’ve all been in a cruddy situation where we have a nice bag of cannabis and no real way to smoke it. It can happen when your main piece breaks, or while out and about after an impulse purchase, and if you don’t have a head shop and some extra spending money, then you are out of luck. This is a scenario most stoners have found themselves in, which is a major motivator for coming up with unique ideas, and this one has been around for ages, with a few tweaks over time.

A good weed pipe needs a strong draw, a seal, a stem, a mouthpiece, and bowl, and all of that might sound like a lot if you’re looking around for materials to use to build each individual piece from scratch, but learning how to make a pipe doesn’t have to be difficult, and it almost never requires more than one type of material if you put your mind to it. This aluminum weed pipe is made from 100% aluminum foil, and you won’t need a screen, glue, or anything else extra to make it all work.

Steps on how to make an aluminum homemade pipe

  • Scissors
  • Aluminum foil
  • Toothpick (or some other sharp-pointed tool)

    To start, you will need a long chunk of aluminum foil, and it’s always best to keep it as wrinkle-free as possible, so be careful while you measure out an arm’s length of it from a roll.

    Lay the aluminum foil down on a clean flat surface and fold it lengthways 3 times. Once you are done, you should have a shape that is close to a square with 3 layers of metal overlapping.

    Now, grab one of the longest edges of the foil and start to bend it inwards into a tube shape. The roll should be about the same thickness as your finger for it to work properly, any bigger and it will be uncomfortable to fit your mouth around, and any smaller and it will be hard to finish the weed pipe without blocking off airflow.

    Make sure that the entire piece of aluminum foil is rolled up, and once you find the edges, use a small amount of moisture or pressure to help hold it all together. Luckily aluminum foil is flexible, so this extra step isn’t always necessary.

    It’s time to make the bowl of your homemade pipe, and it’s as easy as grabbing the widest end of the tube (if there is one) and twisting it just enough that you can bend the tip into a bowl shape before adjusting it so that it points upwards. Sometimes it also helps to keep a toothpick in the end of the tube that’s getting twisted to hold it open enough to maintain airflow.

    Now, take a draw through the open end of the makeshift weed pipe. If you feel too much hesitation, then you might have to untwist it a bit until you feel the seal break. Otherwise, you won’t be able to inhale your weed once it’s lit. If it’s good, then you are ready to move onto the next step.

    You already have the weed pipe you wanted, but one of the major flaws of aluminum is that it heats up really quickly, so if you want to avoid the feeling of hot lips, then you might want to take another chunk of foil, and use it to shape into a mouthpiece that will slide over the open end of the tube. Make sure to give it a gentle squeeze to seal it all up, but once this final step is finished, you are good to go.

    This homemade pipe doesn’t need a screen because the hole inside of the bowl is small enough that it’s just not necessary, but you should know that they aren’t recommended for full-time use. They work as an excellent solution in a pinch, but aluminum foil isn’t going to hold up to more than a few uses before it’s ready for the recycling bin.

    DIY- How to build a functional homemade hookah (shisha)

    This DIY Shisha project calls for enough materials to install one single draw hose, but if you want more, you can always use more rubber tubing and casings.

    This aluminum weed pipe is made from 100% aluminum foil, and you won’t need a screen, glue, or anything else extra to make it all work.

    How To Make A Good Sturdy, Aluminum Foil Pipe

    W1z Khalifa
    Member

    Here’s a video I made today on how to make an aluminum foil pipe in under 5 minutes.

    It works like a charm

    Fullmoon kid
    Active Member

    Wrap the foil around a pencil , remove pencil , place blunt end of pencil in one end of aluminium tube you now have and bend to form a bowl..done..in under 30 secs

    Smoking using foil is not a good idea by the way.

    Zeplike
    Active Member
    W1z Khalifa
    Member
    W1z Khalifa
    Member

    Wrap the foil around a pencil , remove pencil , place blunt end of pencil in one end of aluminium tube you now have and bend to form a bowl..done..in under 30 secs

    Smoking using foil is not a good idea by the way.

    Fullmoon kid
    Active Member
    NI420
    Active Member

    Not a good idea, when heated gives of aluminium oxide a vapour which has been linked to alchimers disease due to alot of people in the generation that is currently elderly bein exposed to aluminium oxide through cookin in aluminium pots? dunno if that true could possibly be an urban ledgend but whos chancin it when a cheap bowel, downpipe and gauzes only cost about 4 of our great british pounds. Also not recomended would be tins!

    W1z Khalifa
    Member

    I know but it’s not like I use aluminum all the time.

    The only time I use one is when I can’t take a piece with me and I need something I can just throw away or if I don’t have a pipe and I just want a quick high.

    The occasional bowl out of tin or aluminum isn’t going to give you Alzheimer’s or hurt you.

    Also, the only reason they THINK that smoking aluminum or tin could be linked to Alzheimer’s is because people with Alzheimer’ have unusually high levels of the chemical in their body.

    Sr. Verde
    Well-Known Member

    If you want a quick smoke you can get rid of roll a joint

    Here's a video I made today on how to make an aluminum foil pipe in under 5 minutes. It works like a charm 😀 http://www.youtube.com/watch?v=iilmMyySrfI