How to Make a Weed Pipe in 6 Ways
Pipes have been a part of the cannabis culture for almost as long as there is one.
In the modern era of cannabis, pipes are perhaps one of the most common ways of smoking weed.
This guide will teach you how to make a pipe in 10 different methods and from various materials – such as plastic, wood, fruit, and more.
In general, there are 2 types of pipes, depending on the materials the pipe is made of:
- Reusable pipes
- One-and-done pipes which are not to be reused
It would be a smart idea to always keep a couple of clean metal pipe bowls around the house which you can get at almost every weed supply store. If you don’t know what those are you can see examples on the image below.
These will come in handy a lot of times when you want to make a makeshift pipe and they help you turn almost anything into a pipe with just a little effort.
#1 Bamboo Pipe
If you can find a thin piece of bamboo (about 2 inches wide) cut it up so that one end is plugged by the sort-of wood membrane bamboo has, and the other end cleanly cut off — as this will be the mouthpiece.
Drill or cut a ½ inch (1.5 cm) hole on the opposite end and use the remaining pieces of the bamboo stick to carve a small bowl for your pipe which you will then fit in the hole you just made.
You should use an even thinner piece of bamboo, preferably one with the wood membrane on the thin end of the stick which will serve as protection against ashe going in your mouth.
All you need to make is a very tiny hole on that membrane and try not to break it completely. If it does break it will still do a fine job at protecting against ashe as long as there are tiny pieces of the membrane left.
#2 The Toilet Bowl
Take a used toilet paper roll and make 2 or 3 holes on one end of it, and cover that end with a thick cloth and a rubber band over it. The holes you just made will be the place where you will insert your joints or blunts.
The opposite end will be your mouthpiece, which is a bit wider than usual, but think about it as a sort of a homemade steam roller. You can press the cloth end while taking a drag for an enhanced and bigger hit.
#3 Pringles Pipe
This is pretty much the same deal as The Toilet Bowl, except for the cloth part, as you don’t have to plug on end. All you have to do is drill a couple holes for your joints to stick ‘em in and pull.
The other way to do this is by making an inch wide hole on the bottom part of the Pringles box and put some aluminum foil in the hole and stick the end of the aluminum outside the hole with some tape, most commonly used is the gray duct tape.
It’s important that you do this right and don’t be afraid to use a bit more foil. If you don’t do this part right the tape might melt and then your pipe might get ruined.
#4 Fruit and Veggie Pipes
Alright so this basically boils down to the same thing with most of the smokable fruits and vegetables – take a pencil shove it all the way through the long part of the fruit.
This will act as the main tube for the smoke to come in.
Then, make another 2 holes that are perpendicular to the tube, and connect them so that smoke may go through. Congrats you just made the bowl and an air vent.
Make a little indent on the place where the bowl is and widen it a bit and start packing that sticky icky. Using a store-bought metal bowl can be a great way to enhance these pipes and make them easier to smoke from.
This method works, as I previously said, on a number of fruits and vegetables such as avocados, pears, melons, watermelons, giant strawberries (yes, we saw and tried them – dope.), bananas, cucumbers, leeks and lots of others.
Apples have been most commonly turned into pipes. As you can see from the image below, you’ll need a pencil to push it through the apple through the middle (sideways) and make a tube, and make another hole where the stem is to connect it with the tube. The hole where the stem was will be your bowl area in which you should pack weed.
#5 Baguette pipe
Are you a baguette fan? Baguettes are a common item across France, some parts of Canada and almost every bakery and pastry shop.
Grab a pencil or a chopstick if you have and drill a hole from one of the pointy ends of the baguette. At the end of that tube drill another smaller hole for your joint or a metal bowl.
Stick a joint in that hole and puff on your baguette like a French gangsta. Heads up – it might taste a bit toasty.
#6 Soda can
Soda cans are even easier to turn into a pipe than a plastic water bottle. Push the can on two sides near the bottom in so you make a little indentation, and then pierce the indented part with a needle or pen so you make a little grill. The grill will hold you weed in place and not let any ashe or weed fly into your mouth while hitting it. Make a hole above it for a little ventilation and easier hitting and you should be ready to light it up!
Help us make more pipes
Do you know any great ways of making a pipe from ordinary items such as a pen or a soda can?
Do you think we missed some great ideas for a makeshift pipe?
Feel free to let us know down in the comment section and we will be happy to write a second part of this article.Pipes are an important staple in the cannabis culture and one of the favorite DIY stoner projects. We teach you how to make 6 unique pipes.
DIY Hollow Out A Light Bulb
When I was growing up I had a keen interest in the sciences. Mostly because of the cool gear that scientists used, you know, beakers, flasks, Bunsen burners that sort of thing. Well, not only did I not have the money for those sorts of thing but I had no idea where to even buy them if I could. So I had to improvise. One of the better improvisations I was able to do was to hollow out a light bulb and use it for other things. The glass that makes the envelope of the build is quite heat resistant and the screw base is good to attach things to (even better if you can find old ones with brass bases, you can solder to those). I made a number of small boilers in order to learn about steam and distillation. I hope to show people that even if a bulb burns out, it can still be useful.
You will need some common tools, a screwdriver (regular) and snips (or needle nose pliers). Use whatever bulb you have handy. *CAUTION* Never use a fluorescent bulb for this project, no matter how cool it looks. The powder used to coat the inside of them is made from phosphor and is quite toxic. You’re also working with glass, so use eye protection! You can’t see mine because I’m wearing them. You should also use gloves or wrap the bulb in a towel just in case it breaks. Yeah, you can’t see mine because i didn’t have any handy. So do as I say and not as I do, got it?
First, grip the little solder point and give it a good twist. You will free the brass contact and break one of the wires leading to the filament.
Once the contact has been pulled out, carefully crack the glass insulator. The chips from this are quite pervasive, they get into just about anything in the area and they are razor sharp. Use caution.
After the insulator has been removed you can see the inside supports of the filament and the fill hole. In the old days bulbs were evacuated of atmosphere to keep the filament from oxidising and burning through. Now days the glass envelope is back filled with an inert gas like argon. The keeps the filament from burning through and makes the bulbs safer.
Use the screwdriver to break the fill tube.
The fill tube could be saved for a later project if you wish.
You can now shake the filament assembly out of the tube. If the tungsten wire is still intact you could probably find a good use for it. You could make another light bulb if your stuck for something to do I suppose.
The bulb needs a good cleaning. This powder, is called kaolin and is pretty safe. You should still be careful and keep it away from your mouth and anything you might eat near.
Mind the sharp bits of glass in the socket when doing this. If you have some stubborn bits inside of it that you can’t get to with this technique you can fill the bulb with a little salt and shake it about. this should scour the powder off the walls.
There you are, an empty light bulb ready for a new lease on life.
As an example I built this neo-Victorian New Age Flemming like valve out of a discarded bulb.
A more traditional use is as a vessel to boil water. I wouldn’t use too hot of a flame, a candle or an alcohol burner should be about as much heat as you should use. It is after all only a light bulb. Real lab ware is much thicker and can take more heat. Still, for the amateur experimenter this can be handy to have.
I hope you have enjoyed this little project and have fun making useful things out of what was once junk.
A few of the dimmer bulbs insist on sending me comments on how this will make great drug paraphernalia. Please keep those comments to yourself as I delete them ASAP. You don’t have to be a rocket scientist to make something into a pipe and that’s not why I wrote this tutorial. Thanks.
Another useful that can be made with a used light bulb (more)DIY Hollow Out A Light Bulb When I was growing up I had a keen interest in the sciences. Mostly because of the cool gear that scientists used, you know, beakers, flasks, Bunsen burners that sort ]]>